一、方管切割：工業制造的「外科手術」

　　1、 Square tube cutting: a surgical procedure in industrial manufacturing

　　想象濟南某鋼結構廠的方管切割現場：一根 80×80mm 的方管要切成精準的 45 度角，誤差超過 0.5mm 就會導致整個框架歪斜 —— 這堪比給鋼鐵做「外科手術」。某濟南橋梁項目曾因切割誤差大，200 根方管報廢，損失相當于 1000 斤章丘大蔥的價值。而掌握這 5 招，切割精度能穩如泰山！

　　Imagine the square tube cutting site of a steel structure factory in Jinan: an 80 × 80mm square tube needs to be cut into a precise 45 degree angle, and an error of more than 0.5mm will cause the entire frame to tilt - this is comparable to performing a "surgical operation" on steel. A bridge project in Jinan once had 200 square tubes scrapped due to large cutting errors, resulting in a loss equivalent to the value of 1000 pounds of Zhangqiu scallions. And with these five moves, the cutting accuracy can be as stable as Mount Tai!

　　二、設備選擇：像選手術刀一樣挑「切割利器」

　　2、 Equipment selection: Choose the "cutting tool" like choosing a surgical knife

　　1. 數控切割機：方管的「CT 定位手術臺」

　　1. CNC cutting machine: "CT positioning operating table" for square tubes

　　精度王者：某濟南重工用伺服電機驅動的切割機，切割 1000mm 方管誤差≤0.1mm，相當于頭發絲直徑的 1/5；

　　Precision King: A cutting machine driven by a servo motor from a certain Jinan Heavy Industry company can cut 1000mm square tubes with an error of ≤ 0.1mm, which is equivalent to 1/5 of the diameter of a human hair;

　　智能校準：設備自帶激光測距儀，開機自動掃描方管變形量，某濟南車廂廠用它后，焊接合格率從 85% 升到 99%。

　　Intelligent calibration: The device comes with a laser rangefinder, which automatically scans the deformation of the square tube when turned on. After a certain Jinan carriage factory used it, the welding qualification rate increased from 85% to 99%.

　　2. 等離子切割機：高速切割的「激光刀」

　　2. Plasma cutting machine: a "laser knife" for high-speed cutting

　　速度與精度并存：切割速度達 1.5m/min，某濟南廚具廠用它切 2mm 薄方管，切口平滑如鏡面；

　　Coexistence of speed and accuracy: The cutting speed reaches 1.5m/min, and a certain Jinan kitchenware factory uses it to cut 2mm thin square tubes, with smooth and mirror like cuts;

　　防抖動設計：切割頭帶磁懸浮穩定裝置，某濟南通風管道廠用它切 6 米長方管，兩端誤差≤0.3mm。

　　Anti shake design: The cutting head is equipped with a magnetic levitation stabilizer, which is used by a ventilation duct factory in Jinan to cut 6-meter rectangular pipes with an error of ≤ 0.3mm at both ends.

　　三、工藝參數：像調相機焦距一樣精準設定

　　3、 Process parameters: precise setting like adjusting the focal length of a camera

　　1. 切割速度：方管的「手術節奏」

　　1. Cutting speed: the "surgical rhythm" of square tubes

　　黃金公式：厚度 4mm 方管最佳速度 1.2m/min，某濟南貨架廠按此調整后，切口毛刺減少 80%；

　　Golden formula: The optimal speed for a 4mm square tube is 1.2m/min. After adjusting according to this, a Jinan shelving factory reduced the burrs on the cut by 80%;

　　反面案例：某濟南小作坊圖快用 2m/min 切割，方管切口像鋸齒，矯正成本比切割費還高。

　　Negative case: A small workshop in Jinan used a cutting speed of 2m/min to cut the square tube, and the cut of the square tube looked like jagged teeth. The cost of correction was even higher than the cutting fee.

　　2. 氣體壓力：決定切口的「出血量」

　　2. Gas pressure: determines the "bleeding volume" of the incision

　　氧氣壓力 0.6MPa 最佳：某濟南壓力容器廠用此壓力切碳鋼方管，氧化層厚度＜0.05mm；

　　The optimal oxygen pressure is 0.6MPa: a Jinan pressure vessel factory uses this pressure to cut carbon steel square tubes with an oxide layer thickness of less than 0.05mm;

　　類比說明：壓力過低像鈍刀割肉，某濟南鐵藝店曾因壓力不足，切廢 30 根方管。

　　Analogous explanation: Low pressure is like a blunt knife cutting meat. A certain Jinan iron shop once cut 30 square tubes due to insufficient pressure.

　　四、工裝夾具：給方管穿「固定鎧甲」

　　4、 Fixture: Thread "fixed armor" into square tubes

　　1. 液壓夾具：方管的「骨折固定器」

　　1. Hydraulic fixture: square tube "fracture fixator"

　　三點定位設計：某濟南機械加工廠的夾具，能將方管晃動量控制在 0.05mm 內；

　　Three point positioning design: The fixture of a certain Jinan mechanical processing factory can control the shaking of the square tube within 0.05mm;

　　實測效果：切割 200×200mm 方管，角度誤差≤0.5 度，相當于濟南趵突泉水位波動的 1/10。

　　Actual test result: Cutting 200 × 200mm square tubes with an angle error of ≤ 0.5 degrees, equivalent to 1/10 of the water level fluctuation of Baotu Spring in Jinan.

　　2. 磁吸式工裝：薄板的「溫柔抓手」

　　2. Magnetic tooling: a "gentle grip" for thin plates

　　磁力可調：某濟南汽車廠切 1.5mm 薄方管，用 0.8T 磁力吸附，避免夾傷表面；

　　Adjustable magnetic force: A certain Jinan automobile factory cuts a 1.5mm thin square tube and uses 0.8T magnetic force to adsorb it, avoiding surface damage;

　　細節設計：工裝表面貼橡膠墊，某濟南儀器廠用后，方管劃痕率從 15% 降到 1%。

　　Detail design: Rubber pads are attached to the surface of the tooling. After being used by a certain Jinan instrument factory, the scratch rate of the square tube decreased from 15% to 1%.

　　五、人員操作：比中醫把脈更講究手感

　　5、 Personnel operation: More emphasis on tactile sensation than traditional Chinese medicine pulse diagnosis

　　1. 預熱技巧：方管的「術前熱敷」

　　1. Preheating technique: "Preoperative hot compress" of square tube

　　厚壁方管必做：切割前用火焰預熱至 200℃，某濟南礦山設備廠用此招，厚 8mm 方管切口裂紋率降為零；

　　Thick walled square tube must be made: Preheat to 200 ℃ with a flame before cutting. A certain Jinan mining equipment factory used this method, and the crack rate of the 8mm thick square tube cut was reduced to zero;

　　溫度控制：用紅外測溫儀確保預熱均勻，某濟南鍋爐廠曾因溫差大，切割后方管變形超 1mm。

　　Temperature control: Use an infrared thermometer to ensure uniform preheating. A certain Jinan boiler factory once deformed the square tube by more than 1mm after cutting due to a large temperature difference.

　　2. 退刀策略：切割的「術后縫合」

　　2. Withdrawal strategy: "Postoperative suturing" for cutting

　　45 度退刀法則：結束時沿切口 45 度退出，某濟南鋼結構公司用此技巧，切口毛刺減少 60%；

　　45 degree retraction rule: At the end, exit along the incision at a 45 degree angle. A certain Jinan steel structure company used this technique to reduce burrs on the incision by 60%;

　　錯誤示范：某濟南工地工人直上直下退刀，切口崩裂像狼牙，返工浪費 3 小時。

　　Error demonstration: A worker at a construction site in Jinan retreated his knife straight up and down, causing the incision to crack like wolf teeth and wasting 3 hours on rework.

　　本文由濟南方管友情奉獻.更多有關的知識請點擊:http://m.95fjrc.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Color Steel Tile For more information, please click: http://m.95fjrc.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.