The installation of colored steel tiles provides a guarantee of use for buildings. This product is sturdy and aesthetically pleasing to use, but most people have limited understanding of its corner cutting process. It is mainly to make its edges neat, so that you will find it more uniform when using it.

便攜式夾芯板節省了大量的安裝時間，因?yàn)樗鄬?duì)堅固，不影響建筑物的強度。同時，其防火性能為建筑增加了保證。它被整齊地切割在邊緣和角落。在后期施工中，特別是在對齊環節時，它會很輕。、多件線按45度斜角多件排列45度角，彩鋼瓦用這種方法切角的加工效率明顯是單件切角的多倍。

Portable sandwich panels save a lot of installation time because they are relatively sturdy and do not affect the strength of the building. At the same time, its fire resistance performance adds assurance to the building. It is neatly cut at the edges and corners. In later construction, especially during the alignment phase, it will be very light The multi piece line is arranged at a 45 degree angle, and the cutting efficiency of color steel tiles using this method is significantly multiple times that of single piece cutting.

2.對稱切割兩件

2. Symmetrically cut two pieces

使用此方法，應提前制作一對夾角90度角的靠板。要切角的線沿著靠板兩側的端面朝向端面90度。對齊刀后，切斷夾芯板的切角部分，一次可切割兩條相互對稱切角的線。此方法僅適用于對稱切角線。如果工作臺允許，也可以同時切割4或8條線。

Using this method, a pair of backup plates with an angle of 90 degrees should be made in advance. The line to be chamfered faces 90 degrees towards the end face along both sides of the backing plate. After aligning the knives, cut off the chamfered part of the sandwich board, and can cut two symmetrical chamfered lines at once. This method is only applicable to symmetric tangent lines. If the workbench allows, 4 or 8 lines can also be cut simultaneously.

3.特殊情況下的切角

3. Corner cutting under special circumstances

線條應切割成45度角。當彩鋼瓦的高度和底部尺寸如此之大，以至于刀片無法切割時，應改變切割角度的方式。新的角度切割方法是將線水平放置，將工作臺旋轉到一定角度，將刀片旋轉到一定角度，調整刀片與線條之間的位置關系，然后切割角度。

The lines should be cut at a 45 degree angle. When the height and bottom size of the colored steel tile are so large that the blade cannot cut, the cutting angle should be changed. The new angle cutting method is to place the line horizontally, rotate the workbench to a certain angle, rotate the blade to a certain angle, adjust the position relationship between the blade and the line, and then cut the angle.

可以看出，彩鋼瓦的切角工藝做得很好，產品在后期使用時會相對穩定。然而，如何處理切割后的棱角是我們判斷制造商產品質量的標準。因此，我們需要注意，在施工過程中也要注意施工中的裂縫，否則會影響后期使用的整體效果。

It can be seen that the cutting process of colored steel tiles is well done, and the product will be relatively stable in later use. However, how to handle the edges and corners after cutting is our standard for judging the quality of manufacturers' products. Therefore, we need to pay attention to the cracks during the construction process, otherwise it will affect the overall effect of later use.